| 设为主页 | 保存桌面 | 手机版 | 二维码
普通会员

上海凯贤印刷科技有限公司(生产部)

PP免处理油墨-自干金属油墨-免烘烤金属油墨-电镀五金油墨-塑胶电镀油墨-阳极氧化铝...

产品分类
  • 暂无分类
站内搜索
 
友情链接
  • 暂无链接
您当前的位置:首页 » 供应产品 » 上海PP免处理油墨-免处理PP油墨-PP油墨
上海PP免处理油墨-免处理PP油墨-PP油墨
点击图片查看原图
产品: 浏览次数:73上海PP免处理油墨-免处理PP油墨-PP油墨 
品牌: 欧莱斯
单价: 180.00元/KG
最小起订量: 1 KG
供货总量: 1000000 KG
发货期限: 自买家付款之日起 2 天内发货
有效期至: 长期有效
最后更新: 2022-07-25
  询价
详细信息

油墨特性:
主要用于ABS、PC、PVC、PS等,具有高色泽、高色彩、高遮盖力、高稳定性、耐酒精及特慢干之特点。(可在30分钟内不需开油洗网)
印刷:选用网目为250- 400目,丝印移印均可。
表干及实干时间:表干时间自然挥发5-10分钟;实干时间在24小时以内,如需快速干燥请烘烤50度20分钟为**效果。
稀释及清洗:783慢干开油水;同时可使用718洗网水清洗。
测试方法(完全干燥后):
13M胶纸粘在画有百格的油墨表面,45度角迅速拉起不脱油;
2纯度99%的酒精,500克砝码用棉布包住在油墨表面,以水平力来回拉100次无脱色。
使用方法:
1使用前应充分搅拌,用后随时封闭;
2搅拌时加开油水10-15%,稀释到印刷粘度;                                  
3网板塞网时可用洗网水清洗;
4不得与其它类型油墨混合使用。
注意事项:
1塑胶材料的外观相似,但可能会是不同的材料,客户需试印确定其符合要求后,再批量印刷;
2在移印过程中,如出现拉丝或散开,可适当加入一些慢干膏即可;
3环境温度过高,将会影响油墨原有质量;
4根据气候变化,请远离火源,阴暗环境下存放。
Ink characteristics: mainly used for ABS, PC, PVC, PS, etc, with the high colour and lustre, high color, high covering power, high stability, resistant to alcohol and slow the characteristics, dry. (can be in 30 minutes don't need to open oil washing nets) printing: choose the mesh is 250-400 mesh, silk screen moving printing all can. Table dry and work time: dry time table natural volatilize 5-10 minutes; Work in time within 24 hours, if need to rapid drying please baking 50 degrees 20 minutes for the best effect. Dilution and cleaning: 783 slow oil and water do open; At the same time, you can use clean water to wash the nets 718. Test method (dry) : 1, 3 M tape is stuck in the picture has the case of printing ink surface, 45 degree Angle quickly pull up not to take off the oil; 2 and purity, 99 and alcohol, 500 grams of Jordan farmar cover with cotton cloth in ink surface, with the level force and 100 times back and forth without decoloring. Method of use: 1, before the use should be fully mixing, after using closed at any time; 2 when the oil and water, stir number 10-15 F dilution to printing viscosity; 3, sheet stuffed nets can be used when washing nets water cleaning; 4, not with other kinds of printing ink mixed use. Note: 1, the appearance of the plastic material similar, but may be different materials, the customer shall determine the ShiYin requirements after another, batch printing; 2, in moving printing process, such as a wire drawing or leave, can be appropriately to add some slow dry paste can
产品规格: 按订单
询价单
0条  相关评论